|
|
|
| General RC Aircraft Discussion Discuss anything RC related |
Topic Review (Newest First)
|
| 10-23-2013 12:21 PM | ||
| davidmc36 |
Re: Need answers: What do I have here??? Quote:
 Best to take it off while playing around with setup. (have it on for balance though of course.)
|
|
| 10-23-2013 12:21 PM | ||
| darcy32171 |
Re: Need answers: What do I have here??? Have to get ready for a funeral. I`ll tune in later this afternoon. |
|
| 10-23-2013 12:20 PM | ||
| davidmc36 |
Re: Need answers: What do I have here??? Quote:
Since I used a small LiPo that was quite light it may have been under the front canopy. Depends on what you use. You could screw a couple servos in just to position them and set the rest of the gear in somewhere and try balancing it with the battery just sitting on top to figure out where to put it. |
|
| 10-23-2013 12:20 PM | ||
| darcy32171 |
Re: Need answers: What do I have here??? You were correct David, must be a spade fuse. I turned the radio on and held the white wires together and could not get any reaction.....then I started hitting toggle switches lol. There is one on top marked "gear", I hit it and that prop was full tilt lol. |
|
| 10-23-2013 12:10 PM | ||
| darcy32171 |
Re: Need answers: What do I have here??? Empty lol. A spot to put a couple servos. |
|
| 10-23-2013 11:56 AM | ||
| davidmc36 |
Re: Need answers: What do I have here??? I bet you could put the two ends of those white wires right on to a blade type fuse. I would only be guessing what value it should be though. Does the power switch have a current rating on it? Duh!! Just re-read and see you said 20 amps. I would go for a 15 amp, protect the power switch from over current. Might find some info or instructions on that switch if you ask good ole' Mr. Google. What does it look like inside the bottom hatch? |
|
| 10-23-2013 11:38 AM | ||
| darcy32171 |
Re: Need answers: What do I have here??? Here are a few pics. That long battery pack is from my roto start for my RC trucks. It is 1800mah 7.4v and was the only one I had with the same type plug. on the power switch box it says 20a 7.2-8.4v so I knew it wouldn`t do any harm. As for the servos, I have a baggy with different type ends (round, t-type, etc) not sure which to use yet. You can see the white wire I speak off with the same ends. Not sure what gets plugged in between to make connection.....maybe a fuse of some sort? I`m just guessing at this point. |
|
| 10-23-2013 11:19 AM | ||
| darcy32171 |
Re: Need answers: What do I have here??? Quote:
|
|
| 10-23-2013 11:14 AM | ||
| davidmc36 |
Re: Need answers: What do I have here??? Quote:
Even in the presence of some tips here, take it to an experienced modeler before attempting flight to have it checked out. |
|
| 10-23-2013 11:09 AM | ||
| darcy32171 |
Re: Need answers: What do I have here??? Thanks. I noticed the prop was tight against the fuselage, Loosened it off and moved it outward a hair. Just with a 1.5v Double A battery I touched both leads and it turns nice. If any of you are wondering and unclear of the white wire I am talking about...just say and I will post a pic. |
|
| This thread has more than 10 replies. Click here to review the whole thread. | ||
Your Privacy Choices