|
|
08-06-2014 08:15 PM | ||
DOUBLEALPHA |
Re: Flyzone DHC-2 Beaver....WOW my beaver |
|
07-17-2014 12:03 AM | ||
Cat 1 |
Re: Flyzone DHC-2 Beaver....WOW Hey fella's.... Sorry for the slow reply... Just stumbled across your posts... I will have to look up my radio settings and Will try to post an explanation here... terrible busy at work so it might take a while to do... |
|
07-15-2014 01:46 AM | ||
Keith Westfall |
Re: Flyzone DHC-2 Beaver....WOW Quote:
Would like to see that posted here if possible! Thanks. |
|
07-14-2014 11:24 PM | ||
Tigger |
Re: Flyzone DHC-2 Beaver....WOW Hi guys , I just joined the RC forum . I have been following it for quite a while as I build up my beaver using many of the great ideas posted . I have the new Mr RC sound card with the lighter TT25 sound generator , fits perfect in front of the rear seat on a piece of 1/8 inch plexiglass epoxied to the floor . Compared to the speaker it sounds louder and there are no holes for water to get in . I am about ready for the maiden flight , but wanted to see if I could get my DX7 to do what Chris S ( Cat 1 ) has done to get the Ailerons to droop with the flaps . Chris of you are out there can you send me the settings to my e mail , describe how you made this work. I tried to open your posted file with my dx7S and it said it was a dx8 file and would not load . Thanks |
|
01-26-2014 09:00 AM | ||
tri5ford |
Re: Flyzone DHC-2 Beaver....WOW Paul, Ref your photo album, Beaver on wheels, what knid/size of wheels are on the Beaver in the pictures taken on the sand, and the upside down shot? Thanks, Gary |
|
01-05-2014 09:41 AM | ||
tri5ford |
Re: Flyzone DHC-2 Beaver....WOW Quote:
From the looks of the pictures, you mounted your receiver in the rear seat area. If this is so, were all leads long enough? Gary |
|
01-04-2014 01:57 PM | ||
tri5ford |
Re: Flyzone DHC-2 Beaver....WOW Hi Paul, I'm Gary and I posted a comment or two on youtube about your DHC-2. You sent your email address to me, and I just surfed here and found you. Nice build album. I bought an AR 600 to install in my DHC-2. Is that what you're using? if so, How did you mount it? As always, any help is greatly appreciated. Gary |
|
05-07-2013 08:29 PM | ||
kem61 |
Re: Flyzone DHC-2 Beaver....WOW Can you tell me how mutch right/down trust there is on the engine,, just repair firewall, motor mount looks ok but i have 5 degree trust is this default setting or i have to make adjustment. thank s in advance Denis. |
|
04-06-2013 12:39 PM | ||
How? |
Re: Flyzone DHC-2 Beaver....WOW Have you guys had any issues with the Anylink? Had a great fight but seem to have interment control problems until part way through 2nd battery lost complete control, until I gathered up the parts and pieces and put them in the van...... |
|
04-04-2013 12:54 AM | ||
Tomahawk |
Re: Flyzone DHC-2 Beaver....WOW They have a website to order the kit and if you like all the parts like motors, esc, glue etc. http://www.wmparkflyers.com/ If you have the Realflight Sim you can also download the MAKO for the sim from the Parkflyers site. Go Shark! Chris |
|
This thread has more than 10 replies. Click here to review the whole thread. |