|
|
|
| Beginners / Newbies Interested in getting in the hobby. Not sure where to start. Post your questions here and one of the RCCanada experts will be glad to help you out! |
Topic Review (Newest First)
|
| 07-29-2015 08:51 AM | ||
| andrewP |
Re: Forgot bind plug in Quote:
|
|
| 07-29-2015 08:49 AM | ||
| andrewP |
Re: Forgot bind plug in just a thought as this happened to me once, check the magnets in the motor... upon crashing one may have come loose or broken? |
|
| 06-25-2015 01:38 PM | ||
| Eye Can Fly |
Re: Forgot bind plug in You should look into how to set your fail-safes, if you haven't already. It isn't that difficult and can save a plane |
|
| 06-25-2015 11:00 AM | ||
| manhoer |
Re: Forgot bind plug in Thank you Floyd it did go into programing mode reset esc and works fine.also thanks to everyone else for helping me trouble shoot this problem.without your help i would have been lost.hopefully someday when i get some experience i can help someone and pay it forward. |
|
| 06-25-2015 08:47 AM | ||
| davidmc36 |
Re: Forgot bind plug in How is your battery powering the ESC? Sounds like it could be low charge or not able to provide enough current and the ESC is doing a low voltage warning. Did you do, if required, a calibration of the ESC to teach it the right throttle channel range of the new Rx? If you put the exact same Rx in I guess it should not need it but......??? Maybe the ESC just failed? I read somewhere of those exact symptoms being a failed ESC. |
|
| 06-25-2015 08:41 AM | ||
| manhoer |
Re: Forgot bind plug in Possible i guess i will google it and try to reprogram the esc.thanks. |
|
| 06-25-2015 12:51 AM | ||
| floyd |
Re: Forgot bind plug in Any chance that you powered up with some throttle which entered the ESC into program mode? Cheers Floyd |
|
| 06-24-2015 10:12 PM | ||
| manhoer |
Re: Forgot bind plug in Adjusted basic settings after i bound reciever.left bind plug in then i tried to throttle up that is when i noticed it was pulsing and low on thrust.seemed to bind properly motor beeped and all that good stuff but no power and surgeing even after i removed binde plug .never flew plane.tried to rebind several times same result every time.could it be the motor even though it worked good before i switched reciever.remember i switched receiver into new plane because i did not realize i needed a receiver for each plane. |
|
| 06-24-2015 09:48 PM | ||
| twistedge |
Re: Forgot bind plug in Let me try to break that down. Plane #1 - Crashed - Replaced ESC - Worked fine - Replaced Receiver - Adjusted settings - Forgot to remove bind plug - Not working now 1. What settings did you adjust? Basic settings like Sub Trim, Servo direction , Rates, etc.. are stored with the model on the Dx6(i). Ideally, you should be able to just a bind the new receiver and keep those basic settings the same. 2. What happened after you did the initial binding process? Did it bind properly? Did you fly the plane? When did it stop working? 3. What's happening now when you power up the system (without the bind plug)? Does the motor beep? Do the servos move? |
|
| 06-24-2015 05:53 PM | ||
| manhoer |
Re: Forgot bind plug in Using spectrum dx6. Eflight pro 30aamp brushless esc.crashed it right out of the box had to replace esc worked fine got new plane so i needed another reciever put oldonein new plane new one in old plane when i foundout had to readjust settings for each plane. now forgot bind plug in and esc doing same thing it was after i crashed it. |
|
| This thread has more than 10 replies. Click here to review the whole thread. | ||
Your Privacy Choices