I Didn’t see that Repair Coming!
The pride of my fleet is a 50cc Midwest Extra 300, Saturday I had been putting it through it’s paces and after four flights it was time to go home. As I was taking the Wing Tube out a piece of Balsa Wood ‘POPPED’ out of the Right Wing and landed on the ground! :confused:
The piece was some 3” x 1” and 1/8” thick…!!?? Where did it come from?!! I spent the next 10 minutes peering into the wing through all of the openings – to no avail… I repeated the exercise at home with the same result. Not good. :( Not wanting to loose this beautiful plane for some stupid reason I decided to do some serious looking early Sunday morning. I picked the most likely spot and cut into the covering, I found a few little things that needed mending in the belly pan but no spot that was missing a large piece of wood… (but I fixed the belly pan concerns while I was there) ;) So I kept cutting off the monokote… and I opened up half of the bottom of the wing. I could not find anything amiss. But what am I looking at/for…? So I cut the monokote off of the bottom of the left wing… and I could not find anything amiss. But what am I looking at…? :BangHead: Now I start doing some comparisons between the two wings and I notice on the Right wing that there is a ‘Rough’ piece of wood near the wing tube…? On the Left wing there is a solid piece of wood! (this is an AHA! Moment) :biggrin: My lost/found piece of wood is a piece of shear bracing. I noticed that the Wing Tube does not butt up against a ‘Stopper’, the WT is actually some 2” too short to meet the nearest rib. So it would seem that during the flights the WT moves and has ‘finally' cut the shear webbing off! I guess the chap that built the plane did not think that the WT would move… :r_c: OK; that’s the problem, now what to do about it!? :confused: I decided to correct the original problem and I built ‘Stoppers’ for the Wing Tube in the wing. Simply – I fit two half sized piece of Shear Bracing in (one on either side of the spars), added some triangular stock to have lots of surface area and then glued on a piece of light ply for the face plate of the ‘Stopper’. I did this in both wings and made sure that there was enough room for the Wing Tube and less than 1/8” of play. (lots of measuring and sanding) ;) So now the underside of both wings are wide open and looks like H3ll, I’ve gone this far why stop now? I never did like that 1” Checker board pattern – so I cut off all of the covering and recovered the entire bottom of the wings with basic beige and a couple of Black ‘Invasion Stripes’. Simple, but effective. :) About this time my Mrs. walked up and asked me why I was here on a Sunday morning and not flying? My explanation did not impress her any more than the time to complete this repair, I started around 6AM and I finished around 2PM. Hey, the job NEEDED to be done and I was in the zone! :biggrin: Only minor touch ups to do now and I will be ready to fly with confidence – next weekend! :TU: :) |
Re: I Didn’t see that Repair Coming!
Makes you feel better when you find the problem and fix it :) Happy flying !!
|
Re: I Didn’t see that Repair Coming!
Good thing you caught that.
Pictures, Rob. Pictures!! :) |
Re: I Didn’t see that Repair Coming!
10 Attachment(s)
Pictures!!?? OMG - I FORGOT! :(
;) OK - there you go - not really much to look at but you can see the before & after plus some of the damage to the nearest rib. A pretty good catch if I do say so. But... by and large I got lucky. I'll take lucky - just don't depend on it all the time. ;) Happy Landings! |
Re: I Didn’t see that Repair Coming!
The RE-MAIDEN was successful! :) :TU:
It did need a bit if trimming... but that is to be expected any time that you remove a servo. ;) I don't care HOW careful you are you NEVER seem to be able to get things aligned EXACTLY the way they were. :itsok_170: Oh well, on to the NEXT project. (there is always another one. ;) ) |
Re: I Didn’t see that Repair Coming!
Nothing wrong with the 80" one piece wings!
|
Re: I Didn’t see that Repair Coming!
Quote:
But Two 40" wings are much easier to transport. ;) |
All times are GMT -5. The time now is 02:17 PM. |
Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Powered by vBA CMPS
vBulletin Security provided by
vBSecurity v2.2.2 (Pro) -
vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.