Register Now

bkrfrmhell · 11-15-2006, 10:45 AM

Building nitroplanes 40 size challenger, uses 2 micro sized servoes for the 4 ailerons. What servo would be acceptable? somewhat economical too, I can't justify spending $90 a servo. i use futaba gear.

FaceDeAce · 11-15-2006, 05:46 PM

The Hitec HS-81 of course!

http://www.hitecrcd.com/Servos/hs81.htm

bkrfrmhell · 11-15-2006, 08:49 PM

So...metal gear or nylon????

ripdivit · 11-15-2006, 09:40 PM

I would go the Hitec HS 85 metal gear. I have had great luck with them and have tortured a them. I have never had the gears strip in an HS 85 MG servo. I have stripped a few HS 81 plastic gears though.

bkrfrmhell · 11-15-2006, 10:19 PM

I will check them out

green@3D · 11-15-2006, 11:20 PM

Would a hitec 225 mg fit. They are a very tough servo. I have started useing them in many of my smaller planes with great results. they are larger than a micro, but much smaller than a standard case size. They are metal gear, or the 225 bb is nylon gear, dual ball bearing

ripdivit · 11-15-2006, 11:36 PM

I agree the 225MG is an awesome servo. The 85MG's are lighter though and should have plenty of torque for Nitro Pitts Challenger ailerons.

11-15-2006, 10:45 AM	#1
bkrfrmhell RCC Senior Contributor I am: Mark Y. Join Date: Jun 2005 Location: Mundare, Alberta # of RCs: 10 Feedback: 0 / 0% Posts: 571 Total Props: 0	What mini servo? 40 size pitts challenger Remove this ad - become a site supporter! Building nitroplanes 40 size challenger, uses 2 micro sized servoes for the 4 ailerons. What servo would be acceptable? somewhat economical too, I can't justify spending $90 a servo. i use futaba gear.
	.

11-15-2006, 05:46 PM	#2
FaceDeAce RCC Supreme Contributor I am: Claude P. Join Date: Sep 2002 Location: Great Western Radio of choice: Futaba 7C and 9C, Prism 7x # of RCs: 20+ Feedback: 8 / 100% Posts: 2,092 Total Props: 1	The Hitec HS-81 of course! http://www.hitecrcd.com/Servos/hs81.htm __________________ Work Hard, Play Harder
	.

11-15-2006, 08:49 PM	#3
bkrfrmhell RCC Senior Contributor I am: Mark Y. Join Date: Jun 2005 Location: Mundare, Alberta # of RCs: 10 Feedback: 0 / 0% Posts: 571 Total Props: 0	servoes So...metal gear or nylon????
	.

11-15-2006, 10:19 PM	#5
bkrfrmhell RCC Senior Contributor I am: Mark Y. Join Date: Jun 2005 Location: Mundare, Alberta # of RCs: 10 Feedback: 0 / 0% Posts: 571 Total Props: 0	servos I will check them out
	.

11-15-2006, 11:20 PM	#6
green@3D RCC Contributor I am: Brian R Join Date: Mar 2005 Location: Blackfalds, Alberta, Can. Planet Earth Feedback: 0 / 0% Posts: 296 Total Props: 0	Would a hitec 225 mg fit. They are a very tough servo. I have started useing them in many of my smaller planes with great results. they are larger than a micro, but much smaller than a standard case size. They are metal gear, or the 225 bb is nylon gear, dual ball bearing __________________ Awww crap my rudder fell off.
	.

11-15-2006, 09:40 PM	#4
ripdivit RCC Apprentice I am: Jeff F Join Date: Oct 2003 Location: Saskatoon, Sk. Feedback: 0 / 0% Posts: 98 Total Props: 0	I would go the Hitec HS 85 metal gear. I have had great luck with them and have tortured a them. I have never had the gears strip in an HS 85 MG servo. I have stripped a few HS 81 plastic gears though.
	.

11-15-2006, 11:36 PM	#7
ripdivit RCC Apprentice I am: Jeff F Join Date: Oct 2003 Location: Saskatoon, Sk. Feedback: 0 / 0% Posts: 98 Total Props: 0	I agree the 225MG is an awesome servo. The 85MG's are lighter though and should have plenty of torque for Nitro Pitts Challenger ailerons.
	.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

vBulletin Message

Cancel Changes

Register Now

Log-in