|
|
06-10-2011, 01:19 AM | #1 |
RCC Pro Contributor
I am: Peter M.
Join Date: Feb 2003
Location: North Bay, ON
Radio of choice:
Futaba 18SZ # of RCs: 22
Feedback: 4 / 100%
Posts: 1,685
Total Props: 26
|
ESC Hazard
Last month, while setting up the electronics for my electric 3D Hobby Shop AJ Slick, I had an interesting experience that could have proved to be the demise of my new aircraft. The servos, ESC (a Hacker X-70 Pro) and motor were already installed in the model and the only thing left to do was set-up the servo rates and end points. Rather than hook-up my 2200 mAh four cell LiPo to power the system through the ESC, I decided to simply plug a standard five cell NiCd airborne pack into the receiver’s extra port, but I didn’t disconnect the ESC from channel three (throttle port) of the receiver. It powered up OK, but after about ten minutes of operation the NiCd batt died; not a big deal because I was pretty well finished with the set-up. Anyway, when I did finally hook-up the LiPo I couldn’t get the motor to run for more than a few seconds before it shut down. Also, when I did hook-up the LiPo, the ESC didn’t give me the customary four “beeps” (indicating a four cell LiPo was connected) followed by two “beeps” that I was use to hearing on start up. Thinking that I might have screwed up the ESC programming when I plugged the NiCd pack into the receiver without first disconnecting the ESC, I tried to reprogram the unit using the traditional throttle stick and “beep” method. Although I did manage to get the system to function, I never did get confirmation that the ESC recognised the four cell LiPo. I’ve been flying the model for a couple of weeks, but I was always concerned about the ESC’s ability to read the LiPo cell count, so I ordered a Hacker ESC programmer to reprogram the ESC properly. When the program arrived, I loaded it onto my computer, hooked up my ESC and learned that the ESC would read a four cell LiPo as only a two cell. What this essentially means is that the ESC would have continued to provide power to the motor and servos, theoretically down to 6.4 volts well below the standard motor cut-off voltage for a four cell and not only potentially damaging the LiPo, but, by the time the motor used up all of the power, there would not have been enough batt left to power the servos! The only thing that saved my aircraft was that I strictly limited my flights to five minutes (based on a friends similar set-up) so my batts were never completely used up. The purpose of this rather lengthy post is, first, to warn others to be careful about hooking up a NiCd to a receiver without first disconnecting the ESC; the lower voltage and capacity of the NiCd could screw up the ESCs programming and secondly, I should have confirmed the correct operation of the ESC before flying; I was lucky that I didn’t loose the aircraft, or worse.
Peter
__________________
Peter Merkel MAAC #22527 Murphy was an optimist; fly safe and have fun. |
. |
Sponsored Links - Subscribe to remove this ad. |
|
06-10-2011, 06:11 AM | #2 |
RCC Supreme Contributor
I am: MERVIN BURKINSHAW
Join Date: Dec 2010
Location: CORONATION ALBERTA
Radio of choice:
HITEC # of RCs: 13
Feedback: 12 / 100%
Posts: 5,780
Total Props: 336
|
Re: ESC Hazard
Thanks Midair, I too have used a nicad pack to set up the radio but have always disconnected the ESC first. Why? Didn't know, just seemed like the thing to do.
Now I know why!
__________________
I never finish anything, I have a black belt in the partial arts! |
. |
06-10-2011, 08:17 AM | #3 |
Administrator
★ Site Supporter ★★ Administrator ★
I am: Max P.
Join Date: Feb 2007
Location: Aurora, Ontario
Radio of choice:
JR and Spektrum Feedback: 77 / 100%
Posts: 19,799
Total Props: 232
|
Re: ESC Hazard
Thank you for a very interesting report, Peter. I learned something from it. I am glad you took the time to share it with us.
I have done the same, but never gave it any thought, You can bet I will be more careful to MAKE SURE the ESC is disconnected next time I do this!
__________________
Transport Canada Advanced Flight Examiner; RC Test Pilot; FPV Instructor, Airplane Instructor; Helicopter Instructor My Aircraft Albums: https://www.rccanada.ca/rccforum/album.php?u=13173 |
. |
|
|
06-10-2011, 07:29 PM | #4 |
Level 3 Supporter
★ Site Supporter ★
I am: Gary L
Join Date: Aug 2008
Location: Tecumseh, Ontario
Feedback: 125 / 100%
Posts: 8,685
Total Props: 101
|
Re: ESC Hazard
Were you successful in reprogramming the ESC?
__________________
I know there's money in aviation........I put it there! |
. |
06-11-2011, 07:54 AM | #5 |
RCC Pro Contributor
I am: Peter M.
Join Date: Feb 2003
Location: North Bay, ON
Radio of choice:
Futaba 18SZ # of RCs: 22
Feedback: 4 / 100%
Posts: 1,685
Total Props: 26
|
Re: ESC Hazard
Yes I was. The computer programmer woks well.
Peter
__________________
Peter Merkel MAAC #22527 Murphy was an optimist; fly safe and have fun. |
. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
waterproof velineon brushless 3500/vxl3s esc combo with esc fan | jumbo2 | FS - Electronics | 4 | 01-07-2011 12:32 PM |
LQQKING for JETI ESC prog box for ( Spin ESC') | satnaam | Wanted - Electronics | 0 | 11-20-2010 08:13 PM |
E-flite 40 amp ESC, align RCE -BL35G ESC+430 L motor for sale | son tran | FS - Electric Gear | 0 | 10-09-2009 05:58 PM |
For Trade GT7 race forward only ESC for Brushless ESC | waylander | WTB + Trade RC Car & Truck items | 0 | 09-26-2008 09:38 PM |
Gas engines and fire hazard | prangled prop | Engines | 16 | 09-08-2004 07:51 AM |