|
|
|
| Multi Rotor Discussion Tri's, Quad's, Hex'as and more. Discuss anything multi-rotor, including multi-rotor stabilization and FPV setups. |
 |
|
|
Thread Tools | Display Modes |
|
|
06-29-2013, 08:45 PM
|
#1 |
|
RCC Expert Contributor
I am: The cookie monster
Join Date: Oct 2008
Location: Whitby, ont
Radio of choice:
Futaba baby!!! # of RCs: 911
Feedback: 8 / 90%
Posts: 764
Total Props: 7
|
Naza help needed
I am just getting my dji 550 ready to go, but my naza with gps keeps flashing red green yellow. I also cant seem to get the motors to turn on. I know it says to put the sticks to opposite corners but im having no luck. I have a futaba 10c, so Im not sure if I have to reverse the throttle channel like normal?
Its naza m version one. I am running the firmware 3.12 though. Maybe thats the problem? It lets me calibrate the transmitter stick position ok, as well as the flight mode and ioc stick. Thanks guys Brad
__________________
|
|
 .
|
|
06-29-2013, 08:56 PM
|
#2 |
|
RCC Expert Contributor
I am: The cookie monster
Join Date: Oct 2008
Location: Whitby, ont
Radio of choice:
Futaba baby!!! # of RCs: 911
Feedback: 8 / 90%
Posts: 764
Total Props: 7
|
Re: Naza help needed
I just realized that I didnt calibrate the gps compass. Maybe thats the problem?
__________________
|
|
|
.
|
|
06-30-2013, 05:54 AM
|
#3 |
|
Administrator
★ Site Supporter ★★ Administrator ★
I am: Max P.
Join Date: Feb 2007
Location: Aurora, Ontario
Radio of choice:
JR and Spektrum Feedback: 77 / 100%
Posts: 19,799
Total Props: 232
|
Re: Naza help needed
Follow the manual to the letter.
I just set up my V2 in about 1 hour by following the manual step by step, and also using the software. Make sure you check each tab in each section of the basic and advanced headers when setting it up using the software.
__________________
Transport Canada Advanced Flight Examiner; RC Test Pilot; FPV Instructor, Airplane Instructor; Helicopter Instructor My Aircraft Albums: https://www.rccanada.ca/rccforum/album.php?u=13173 |
|
|
.
|
|
06-30-2013, 08:12 AM
|
#4 |
|
RCC Expert Contributor
I am: The cookie monster
Join Date: Oct 2008
Location: Whitby, ont
Radio of choice:
Futaba baby!!! # of RCs: 911
Feedback: 8 / 90%
Posts: 764
Total Props: 7
|
Re: Naza help needed
It's the new firmware. Went back to the old firmware and all is good now.
__________________
|
|
|
.
|
|
06-30-2013, 11:58 AM
|
#5 |
|
RCC Pro Contributor
I am: Max Standen
Join Date: Mar 2009
Location: Edmonton, Alberta
Radio of choice:
Futaba 10C # of RCs: 14
Feedback: 9 / 100%
Posts: 1,538
Total Props: 6
|
Re: Naza help needed
I know it was a bit of a pain to setup with the 10c but man is it ever worth it!
__________________
Trex 600EFL Pro DFC ,EG Aircraft Mxs-R Matt Hall DLE 111 pro Flow canisters, Extreme composite Sukhoi, Ritewing Zephry 2 FPV, Twin Star FPV, DJI 550 Hexa FPV. Max Standen. Trout Farm Flyers Team Pro-Rc |
|
|
.
|
|
06-30-2013, 01:02 PM
|
#6 |
|
RCC Expert Contributor
I am: The cookie monster
Join Date: Oct 2008
Location: Whitby, ont
Radio of choice:
Futaba baby!!! # of RCs: 911
Feedback: 8 / 90%
Posts: 764
Total Props: 7
|
Re: Naza help needed
I got the maiden done. The altitude isn't holding worth a damn and gain is at 100 percent. Will bump it up and try again
__________________
|
|
|
.
|
|
06-30-2013, 01:04 PM
|
#7 |
|
RCC Expert Contributor
I am: The cookie monster
Join Date: Oct 2008
Location: Whitby, ont
Radio of choice:
Futaba baby!!! # of RCs: 911
Feedback: 8 / 90%
Posts: 764
Total Props: 7
|
Re: Naza help needed
This is my first multicopter so this is all new to me!!
__________________
|
|
|
.
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
Hybrid Mode
Your Privacy Choices