Register Now

ken park · 11-20-2007, 06:20 AM

Anyone?

moo · 11-20-2007, 08:43 AM

A piece of a slate pool table?

Did I win anything?

ken park · 11-20-2007, 08:55 AM

Wrong not a slate from a pool table!

I think your referring to blue/gray board on the work bench - thats a center wooden section from of an old table I use to own. Its good for cutting and drilling on.

Need a clue?

About the model.

rusty33 · 11-20-2007, 09:30 AM

OK, I'll bite Ken. I mean, 'Ok Ken, I'll bite'.

Take a look at this great site I found...

http://www.mraerodesign.com/SharkE/SharkE-EN.html

Do I win one?

Or are you taking about the glue caddy? Pretty cool as well.

rusty

ken park · 11-20-2007, 10:15 AM

Way to go Rusty! Yes its another SHARK-E

I had this one sitting around my basement waiting to get built - I figure I'll do her up in Black Monokote - should look real cool!

Hey Rusty - You just won my newest design " The Glue Box"
Martin Rousseau going to soon update his own website with this item.
He's had some good size orders sent his way from Hobby shops in the US etc.

I figure I can part with 10$ today for this game.

rusty33 · 11-21-2007, 09:51 AM

Ken that's awesome. Thanks. I just finished building 'Man's Land', a 26'x30' shop with a loft, so I need to fill it will modelling stuff

WRT your new Shark project, what is your power setup?

I sent you a pm.

rusty

ken park · 11-21-2007, 11:19 AM

The model is designed to be equal too a 2 stroke .15 size so I went with the Eflite 15power Brushless 3S 2100 lipo and 40 speedcontroller

I get about 15 min of good flying both fast/slow got clocked doing 187km/hr out of a dive mind you! this summer with a speed gun
Best results with high pitch 8/8 or 8/10 APC prop

No problem with heating of equipment with the big natural airscoop under the nose - air exits out fake jet exhaust cone. In the late fall or winter just stuff some paper in the scoop to keep the cold out.

ken park · 11-24-2007, 12:54 PM

Just finished up the construction part of the build - Even got the 2 x HS-55 servo's mounted one in each wing on the servo doors and hooked up using a Y-harness. Overall Iam very happy with the fit/quality of the laser cut part made the build so much more speedy

See the simple Aileron set up - Servo doors get screwed down into place from below for access when model is covered.

ken park · 11-30-2007, 06:38 AM

Hey Rusty - I just got an email back from Martin and he's doing the burn/posting of your Glue box's today! You should get it prob late next week at worst case I bet.

I got a photo back from a Nice guy in Halifax who just got his yesterday!
He opted for his Handle to be lasered on! He then said when his buddies dropped in they all went home and put in orders too.

rusty33 · 11-30-2007, 03:45 PM

thanks for the update Ken.

More build photos of the Shark please!

11-20-2007, 06:20 AM	#1
ken park RCC Supreme Contributor I am: Ken Park Join Date: Jun 2003 Location: OTTAWA Feedback: 0 / 0% Posts: 2,320 Total Props: 7	What is this? on my workbench Remove this ad - become a site supporter! Anyone? Attached Thumbnails __________________ Not Happy? - Form your own Jet club "OVJ"
	.

11-20-2007, 08:43 AM	#2
moo RCC Supreme Contributor I am: eric q Join Date: Jun 2005 Location: Crawford Lake, Ontario Radio of choice: Turborix # of RCs: too Feedback: 9 / 100% Posts: 7,148 Total Props: 27	A piece of a slate pool table? Did I win anything? __________________ desiderantes meliorem patriam To err is human, to moo is bovine
	.

11-20-2007, 08:55 AM	#3
ken park RCC Supreme Contributor I am: Ken Park Join Date: Jun 2003 Location: OTTAWA Feedback: 0 / 0% Posts: 2,320 Total Props: 7	Agh! - Wrong - Thank you for playing. Wrong not a slate from a pool table! I think your referring to blue/gray board on the work bench - thats a center wooden section from of an old table I use to own. Its good for cutting and drilling on. Need a clue? About the model. __________________ Not Happy? - Form your own Jet club "OVJ"
	.

11-20-2007, 10:15 AM	#5
ken park RCC Supreme Contributor I am: Ken Park Join Date: Jun 2003 Location: OTTAWA Feedback: 0 / 0% Posts: 2,320 Total Props: 7	DING DING DING DING!!! We got a winner! Congrats! Way to go Rusty! Yes its another SHARK-E I had this one sitting around my basement waiting to get built - I figure I'll do her up in Black Monokote - should look real cool! Hey Rusty - You just won my newest design " The Glue Box" Martin Rousseau going to soon update his own website with this item. He's had some good size orders sent his way from Hobby shops in the US etc. I figure I can part with 10$ today for this game. Attached Thumbnails __________________ Not Happy? - Form your own Jet club "OVJ"
	.

11-21-2007, 11:19 AM	#7
ken park RCC Supreme Contributor I am: Ken Park Join Date: Jun 2003 Location: OTTAWA Feedback: 0 / 0% Posts: 2,320 Total Props: 7	Eflite 15power motor Brushless The model is designed to be equal too a 2 stroke .15 size so I went with the Eflite 15power Brushless 3S 2100 lipo and 40 speedcontroller I get about 15 min of good flying both fast/slow got clocked doing 187km/hr out of a dive mind you! this summer with a speed gun Best results with high pitch 8/8 or 8/10 APC prop No problem with heating of equipment with the big natural airscoop under the nose - air exits out fake jet exhaust cone. In the late fall or winter just stuff some paper in the scoop to keep the cold out. Attached Thumbnails __________________ Not Happy? - Form your own Jet club "OVJ"
	.

11-20-2007, 09:30 AM	#4
rusty33 RCC Senior Contributor I am: dave a Join Date: Mar 2006 Location: winnipeg Feedback: 2 / 100% Posts: 504 Total Props: 0	OK, I'll bite Ken. I mean, 'Ok Ken, I'll bite'. Take a look at this great site I found... http://www.mraerodesign.com/SharkE/SharkE-EN.html Do I win one? Or are you taking about the glue caddy? Pretty cool as well. rusty
	.

11-21-2007, 09:51 AM	#6
rusty33 RCC Senior Contributor I am: dave a Join Date: Mar 2006 Location: winnipeg Feedback: 2 / 100% Posts: 504 Total Props: 0	Ken that's awesome. Thanks. I just finished building 'Man's Land', a 26'x30' shop with a loft, so I need to fill it will modelling stuff WRT your new Shark project, what is your power setup? I sent you a pm. rusty
	.

11-24-2007, 12:54 PM	#8
ken park RCC Supreme Contributor I am: Ken Park Join Date: Jun 2003 Location: OTTAWA Feedback: 0 / 0% Posts: 2,320 Total Props: 7	Construction at an end - "BARE - BONES" SHARK-E Just finished up the construction part of the build - Even got the 2 x HS-55 servo's mounted one in each wing on the servo doors and hooked up using a Y-harness. Overall Iam very happy with the fit/quality of the laser cut part made the build so much more speedy See the simple Aileron set up - Servo doors get screwed down into place from below for access when model is covered. Attached Thumbnails __________________ Not Happy? - Form your own Jet club "OVJ"
	.

11-30-2007, 06:38 AM	#9
ken park RCC Supreme Contributor I am: Ken Park Join Date: Jun 2003 Location: OTTAWA Feedback: 0 / 0% Posts: 2,320 Total Props: 7	Your prize Glue Box is getting cut today/posted ok! Hey Rusty - I just got an email back from Martin and he's doing the burn/posting of your Glue box's today! You should get it prob late next week at worst case I bet. I got a photo back from a Nice guy in Halifax who just got his yesterday! He opted for his Handle to be lasered on! He then said when his buddies dropped in they all went home and put in orders too. Attached Thumbnails __________________ Not Happy? - Form your own Jet club "OVJ"
	.

11-30-2007, 03:45 PM	#10
rusty33 RCC Senior Contributor I am: dave a Join Date: Mar 2006 Location: winnipeg Feedback: 2 / 100% Posts: 504 Total Props: 0	thanks for the update Ken. More build photos of the Shark please!
	.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

vBulletin Message

Cancel Changes

Register Now

Log-in