|
|
|
| Electronics Discuss radios, chargers, etc... |
 |
|
|
Thread Tools | Display Modes |
03-24-2013, 01:06 PM
|
#11 |
|
Level 3 Supporter
★ Site Supporter ★
I am: Richard N
Join Date: Mar 2003
Location: Tamworth Area
Radio of choice:
Graupner MC28 & MC20 & MZ-32 # of RCs: 24
Feedback: 72 / 100%
Posts: 2,337
Total Props: 32
|
Re: Telemetry Connector Question
David
I hooked up one of the 10K 1% thermistors that I got from Sayal and it indicated 21C on the Graupner Screen Temp 1 & 2. The General Engine Module has two temp inputs and they both read the same value. I checked it with the thermometer in my shop and it indicated 21C also. I would have to do the ice water/boiling water trick to calibrate but I would bet it is okay. The cheap ones on eBay are rated at 5% but for that price you could probably throw out the ones that are out of wack and still be ahead. LOL Richard |
|
 .
|
| Sponsored Links - Subscribe to remove this ad. |
|
|
|
03-24-2013, 01:21 PM
|
#12 |
|
RCC Supreme Contributor
I am: David C
Join Date: Jul 2010
Location: Morewood, ON
Radio of choice:
DX18 Stealth Taranis X9D+ DX3S # of RCs: 1E
Feedback: 94 / 100%
Posts: 4,912
Total Props: 110
|
Re: Telemetry Connector Question
Right on, I was leaning toward the 1% ones if I were to try and make some but you are probably right about the 5% ones.
__________________
No Bounce-No Play The one who dies with the most toys wins! Electric flying is pretty much seeing how close to a dead short you can run without setting it on fire. 34453  Weather Station |
|
|
.
|
|
03-29-2013, 08:07 PM
|
#13 |
|
Level 3 Supporter
★ Site Supporter ★
I am: Richard N
Join Date: Mar 2003
Location: Tamworth Area
Radio of choice:
Graupner MC28 & MC20 & MZ-32 # of RCs: 24
Feedback: 72 / 100%
Posts: 2,337
Total Props: 32
|
Re: Telemetry Connector Question
I got some connectors yesterday and they fit properly I needed four pin and I have some 8 pin on the way.
They are Micro JST 1.5. I mic'd the pins and they are 1.5mm and fit perfectly. http://www.ebay.com/itm/121081276952...84.m1497.l2649 Last edited by cloudniner; 03-30-2013 at 10:45 AM. |
|
|
.
|
|
|
|
|
04-13-2013, 03:18 AM
|
#14 |
|
Level 3 Supporter
★ Site Supporter ★
I am: Richard N
Join Date: Mar 2003
Location: Tamworth Area
Radio of choice:
Graupner MC28 & MC20 & MZ-32 # of RCs: 24
Feedback: 72 / 100%
Posts: 2,337
Total Props: 32
|
Re: Telemetry Connector Question
I got the 8-pin connectors today and they fit as well. I am using these to wire up a connector to hook up to the Lipo balance connector and then into the Graupner GEM. This will give the individual cell voltages of a 6s pack on the MC20 telemetry screen.
JST Micro 1.5 http://www.ebay.com/itm/111025298770...84.m1497.l2648 Last edited by cloudniner; 04-13-2013 at 03:24 AM. |
|
|
.
|
|
04-15-2013, 01:29 PM
|
#15 |
|
Level 3 Supporter
★ Site Supporter ★
I am: Richard N
Join Date: Mar 2003
Location: Tamworth Area
Radio of choice:
Graupner MC28 & MC20 & MZ-32 # of RCs: 24
Feedback: 72 / 100%
Posts: 2,337
Total Props: 32
|
Re: Telemetry Connector Question
I got the 10K Thermistors today and hooked up five of them and they all indicated 21C. The price is right for sure.
These work with the Spek telemetry modules. http://www.ebay.com/itm/280846915639...84.m1497.l2648 Last edited by cloudniner; 04-15-2013 at 04:37 PM. |
|
|
.
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| EC3 connector | Rossco | Beginners / Newbies | 10 | 07-19-2012 10:29 PM |
| Futaba connector | nairbg | Electronics | 3 | 11-22-2009 04:47 PM |
| Lipo without balance connector | JMLG1971 | Electric Flight | 5 | 04-01-2007 10:39 AM |
| Simulator connector | sorkai | Electronics | 7 | 11-30-2004 06:17 PM |
| Z connector wires | Rodonets | Wanted - Electronics | 0 | 09-19-2003 07:05 PM |
Linear Mode
Your Privacy Choices