Register Now

imported_maximus · 03-08-2008, 07:56 PM

Well hello there, this is my second post on this forum...but I see we now have a dedicated engine room !! Anyways I am from Winnipeg, I modify nitro engines, I specialize in port re-shaping and engine timing alterations.... Some of you may have seen my mills run at the Canadian Winter Nationals In Redeer the last couple of years.... I had 6 engines running there this year and hopefully twice as many next year...

Anyways here are a few snap shots of my work... I will have to upload a few more to photobucket when I get time I guess...

imported_maximus · 03-08-2008, 08:07 PM

Speed Metal · 03-08-2008, 08:21 PM

Nice work Max!! Very clean and sharp work. Good to see a fellow Canadian modder as there doesn't seem to be as many of us as there are in the USA.

regards

speed metal

imported_maximus · 03-08-2008, 08:26 PM

Quote:

Originally Posted by Speed Metal

Nice work Max!! Very clean and sharp work. Good to see a fellow Canadian modder as there doesn't seem to be as many of us as there are in the USA.

regards

speed metal

thank you for the compliments... I know 1 other Canadian modder and thats about it.......

SHEP · 03-08-2008, 08:29 PM

looks fancy

imported_maximus · 03-08-2008, 08:36 PM

here is a X-Dyno report of a Picco 28 that I modified...there are 4 different runs all posted on the same graph... They dyno operator was testing several different setups.. This is the same dyno system XRC uses, I send my motors to my freind Adam from AB Mods to be tested. But this summer I will most likely be purchasing my own X-Dyno....

imported_maximus · 03-09-2008, 01:37 PM

Here is a cheezy little video we shot of cheap STS 30 that I had modified... This motor was extremely fast but it didn't last overly long... Taiwanese meatals and big HP usually dont work too well together..

http://video.google.ca/videoplay?doc...49442354166245

this Truggy is running 30K in the center and a 15 th clutch bell

imported_maximus · 03-09-2008, 01:44 PM

Last year we brought the same STS 30 to the Nationals...was our very first time racing Truggy, and our first time on a clay track..... I ended up getting Jammin Jay to drive Nick's truck ( which was mine at the time LOL) .... anyways heres the video

http://video.google.ca/videoplay?doc...28876071958072

imported_xxfile · 03-09-2008, 02:09 PM

It would really be cool if you took before/after pix as you were doing one so we could see the difference.
looks good

sniff_nitro · 03-09-2008, 02:13 PM

Wow nice job

03-08-2008, 07:56 PM	#1
imported_maximus RCC Junior Contributor Join Date: Jun 2007 Feedback: 0 / 0% Posts: 139 Total Props: 0	PIctures of my engine work Remove this ad - become a site supporter! Well hello there, this is my second post on this forum...but I see we now have a dedicated engine room !! Anyways I am from Winnipeg, I modify nitro engines, I specialize in port re-shaping and engine timing alterations.... Some of you may have seen my mills run at the Canadian Winter Nationals In Redeer the last couple of years.... I had 6 engines running there this year and hopefully twice as many next year... Anyways here are a few snap shots of my work... I will have to upload a few more to photobucket when I get time I guess...
	.

03-08-2008, 08:21 PM	#3
Speed Metal RCC Master Contributor I am: Bill N. Join Date: Apr 2006 Location: Purgatory (Ontario) Feedback: 0 / 0% Posts: 1,284 Total Props: 0	Nice work Max!! Very clean and sharp work. Good to see a fellow Canadian modder as there doesn't seem to be as many of us as there are in the USA. regards speed metal __________________ Chequing Account Factory Team Driver. Proudly sponsored by debt and taxes.
	.

03-09-2008, 02:09 PM	#9
imported_xxfile RCC Expert Contributor Join Date: Nov 2004 Feedback: 0 / 0% Posts: 828 Total Props: 0	Before/After pix It would really be cool if you took before/after pix as you were doing one so we could see the difference. looks good
	.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-08-2008, 08:07 PM	#2
imported_maximus RCC Junior Contributor Join Date: Jun 2007 Feedback: 0 / 0% Posts: 139 Total Props: 0
	.

03-08-2008, 08:29 PM	#5
SHEP Join Date: Jul 2004 Feedback: 0 / 0% Posts: 233 Total Props: 0	looks fancy
	.

03-08-2008, 08:36 PM	#6
imported_maximus RCC Junior Contributor Join Date: Jun 2007 Feedback: 0 / 0% Posts: 139 Total Props: 0	here is a X-Dyno report of a Picco 28 that I modified...there are 4 different runs all posted on the same graph... They dyno operator was testing several different setups.. This is the same dyno system XRC uses, I send my motors to my freind Adam from AB Mods to be tested. But this summer I will most likely be purchasing my own X-Dyno....
	.

03-09-2008, 01:37 PM	#7
imported_maximus RCC Junior Contributor Join Date: Jun 2007 Feedback: 0 / 0% Posts: 139 Total Props: 0	Here is a cheezy little video we shot of cheap STS 30 that I had modified... This motor was extremely fast but it didn't last overly long... Taiwanese meatals and big HP usually dont work too well together.. http://video.google.ca/videoplay?doc...49442354166245 this Truggy is running 30K in the center and a 15 th clutch bell
	.

03-09-2008, 01:44 PM	#8
imported_maximus RCC Junior Contributor Join Date: Jun 2007 Feedback: 0 / 0% Posts: 139 Total Props: 0	Last year we brought the same STS 30 to the Nationals...was our very first time racing Truggy, and our first time on a clay track..... I ended up getting Jammin Jay to drive Nick's truck ( which was mine at the time LOL) .... anyways heres the video http://video.google.ca/videoplay?doc...28876071958072
	.

03-09-2008, 02:13 PM	#10
sniff_nitro RCC Noob Join Date: Mar 2008 Feedback: 0 / 0% Posts: 24 Total Props: 0	Wow nice job
	.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

vBulletin Message

Cancel Changes

Register Now

Log-in