|
|
|
| ARF / ARC Aircraft Discuss anything and everything ARF or ARC related. |
 |
|
|
Thread Tools | Display Modes |
04-07-2012, 04:29 PM
|
#1 |
|
RCC Contributor
I am: Yvan D
Join Date: Sep 2011
Location: Terrebonne Quebec
Radio of choice:
futaba # of RCs: 5
Feedback: 0 / 0%
Posts: 351
Total Props: 2
|
pull pull wire question.
Hello All.
On my mxsr, as recomended the pull pull wire are installed criss crossing... meaning left elev. on right side of servo arm and vise versa. now where wires comes into an X. they are touching each others. Question, will this cause interferences on the 2.4 receiver ??? If yes , any solutions ? TY |
|
 .
|
| Sponsored Links - Subscribe to remove this ad. |
|
|
|
04-07-2012, 05:31 PM
|
#2 |
|
RCC Supreme Contributor
I am: Michel G
Join Date: Apr 2006
Location: Saint-Jerome Quebec Canada
Feedback: 3 / 100%
Posts: 3,316
Total Props: 12
|
Re: pull pull wire question.
Hi
I,m sure someone will answer youre question , but , can you slip a piece of silicone tubeing over one wire . Just a thought . Michel
__________________
M.A.A.C. 75640 Hitec Aurora 9 LT-40 LT-60 Alpha-40 Tiger-60 (90 ) ARF P-51 40 TF-P51 Giant KIT TopFite P-51 Giant ARF X 3 Hanger 9 SpitFire 60 ARF X2 TopFlite Elder-40 ( on the board ) Aero Works 540 T -60 The Ground came up and hit my plane 
|
|
|
.
|
|
04-07-2012, 06:45 PM
|
#3 |
|
RCC Expert Contributor
I am: Dave C
Join Date: Jan 2006
Location: Pitt Meadows,B.C.
Radio of choice:
DX-18 # of RCs: 40+
Feedback: 15 / 100%
Posts: 885
Total Props: 12
|
Re: pull pull wire question.
I usually run the cables through a length of yellow inner nyrod. Also makes it easy to thread the cables through the fuse.
Once the cables are tensioned (not too tight!) I glue and zip tie the nyrod to a convenient bulkhead or cross beam.
__________________
Dave C Pitt Meadows B.C. maac 37241 |
|
|
.
|
|
|
|
|
04-07-2012, 07:06 PM
|
#4 |
|
RCC Supreme Contributor
I am: Terry J
Join Date: Sep 2002
Location: Moncton, NB
Radio of choice:
DX18Stealth # of RCs: 10
Feedback: 115 / 100%
Posts: 3,422
Total Props: 55
|
Re: pull pull wire question.
Or just criss cross your wires and don't worry about it. I've never had an issue.
|
|
|
.
|
|
04-07-2012, 09:49 PM
|
#5 |
|
RCC Contributor
★ Site Supporter ★
I am: Pat B.
Join Date: Jan 2011
Location: Moncton, NB
Radio of choice:
Spektrum DX8 # of RCs: 4
Feedback: 20 / 100%
Posts: 489
Total Props: 6
|
Re: pull pull wire question.
I have the 50CC MXSR, with crossed wires. I've never had issues. If you're worried about chaffing, on the rudder servo horn, you could put a couple of washers under the swivel ball link to raise one wire a few mm's.
__________________
MAAC #83261 |
|
|
.
|
|
04-07-2012, 10:15 PM
|
#6 |
|
Authorized Vendor
★ Vendor ★
I am: Jeff K
Join Date: Jun 2004
Location: Windsor, ON
Feedback: 24 / 100%
Posts: 1,119
Total Props: 10
|
Re: pull pull wire question.
You can use this pull pull cable:
http://www.thunderboltrc.com/index.p...oducts_id=1166 It is Stainless Steel Nylon coated cable - also, check out the Secraft Pull Pull fittings - this setup is the best pull pull setup I've seen. Very easy to adjust and tighten: Secraft Easy Couplers: http://www.thunderboltrc.com/index.p...oducts_id=1168 Secraft Wire Tensioners: http://www.thunderboltrc.com/index.p...oducts_id=1171 Also, if you don't want to use metal cable - you could try Nylon coated Kevlar: http://www.thunderboltrc.com/index.p...roducts_id=580 Grizak
__________________
www.thunderboltrc.com |
|
|
.
|
|
04-07-2012, 10:21 PM
|
#7 |
|
RCC Pro Contributor
|
Re: pull pull wire question.
No issue. Connect one side to the underside of the servo horn and the other to the top side of the servo horn.I have had many 2.4 spektrum set ups this way no issues. With older FM it could be an issue. Use coated wire. Fishings tackle stores sell good quality thin strong coated steel tracer.
|
|
|
.
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Airplane setup - with elevator Pull - Pull. | Gary Maker | ARF / ARC Aircraft | 3 | 08-23-2008 11:59 PM |
| push pull wire | OSS | Scale Aerobatics | 3 | 10-18-2007 03:51 AM |
| Wild Hare Extra 300 Special Pull-Pull Setup | Todd | Giant Scale Aircraft | 2 | 03-09-2004 08:31 AM |
| PULL PULL WIRES. DO THEY INTERFERE WITH RADIO ? | SpaceCowboy | Construction Ideas, Hints and Tips | 13 | 02-25-2004 07:21 PM |
| TDK pull-pull system -------SOLD------- | paul svec | FS - Other RC | 1 | 01-02-2003 10:47 PM |
Linear Mode
Your Privacy Choices