Register Now

imported_sevenstar · 12-23-2004, 07:07 PM

my damn picco is being a pain in the butt....first the high speed niddle o-ring was worn because it screamed like crazy when I started it the other day...I replaced it and set it flush with the top...tryed to start it and the same thing screamed like hell..as I swore like a mad man I shut it off .....than pullstart broke the same day(wooot) so pulled the motor out and changed the clutch bell put new bearing it fine. Then a guy I know told me to play with the low speed niddle and mess with the idle screw and still the same thing so I need so help badly...PLEASE HELP me

Guest · 12-23-2004, 07:36 PM

Teo things I can suggest.

1. starter box or electric start believe me you will thank me

2. for god sake sell that boat anchor and buy an OS

spond · 12-24-2004, 08:16 AM

the instructions are very informative with this particular engine...
Have you broke it in.. or is taht what you are trying..
What vehicle...
waht is your experience with nitro.

The are many people here with piccos, and most like them,...

*John Bakker* · 12-24-2004, 11:36 AM

Sounds like you have an air leak.Check the fuel lines,feul filter ,gas tank,carb boot ,o rings...

imported_sevenstar · 12-24-2004, 01:24 PM

thanx for the input OS I know they are good motors but I have a os 18 in my t-maxx and it works fine but my savage kicks a-- with that picco and the motor is broken in a long time ago I replaced the o-ring it the high speed valve and that did nothing for it. Starter box noway...I was thinking about a tiger drive to replace the pullstart problem!!

imported_REVOS5 · 12-24-2004, 03:48 PM

get a simple hpi roto

Abiye · 12-24-2004, 06:46 PM

take the motor apart and seal the carb and backplate with permatex ultra copper... make sure your head screws and glow plug are tight... i'm pretty sure you've got some experince tuning since you have a tmaxx and savage but check the idle screw as well... since its coldoutside you need to richen up the mixture... even though the engine temps will be low... but i'm pretty sure u knew all that... just take it apart and seal it... while its apart you can check if there is anything physically wrong with it...

12-23-2004, 07:07 PM	#1
imported_sevenstar Join Date: Nov 2004 Feedback: 0 / 0% Posts: 142 Total Props: 0	Ofna picco 26 problem....HELP!!!!!!!!!!! Remove this ad - become a site supporter! my damn picco is being a pain in the butt....first the high speed niddle o-ring was worn because it screamed like crazy when I started it the other day...I replaced it and set it flush with the top...tryed to start it and the same thing screamed like hell..as I swore like a mad man I shut it off .....than pullstart broke the same day(wooot) so pulled the motor out and changed the clutch bell put new bearing it fine. Then a guy I know told me to play with the low speed niddle and mess with the idle screw and still the same thing so I need so help badly...PLEASE HELP me
	.

12-24-2004, 08:16 AM	#3
spond Alumni Mod I am: Scott P Join Date: Jun 2004 Location: Killaloe Feedback: 0 / 0% Posts: 2,240 Total Props: 0	the instructions are very informative with this particular engine... Have you broke it in.. or is taht what you are trying.. What vehicle... waht is your experience with nitro. The are many people here with piccos, and most like them,... __________________ SUPERD's PAST PITMAN just ask SuperD Sprucewood - First B-main, 9th A-main Bellvegas - 4th A-MAIN Truggy TTR S3 - Rossi M21 (on side lines all summer) TTR ST-1 with LSK OMG.. Savage Racer -
	.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-23-2004, 07:36 PM	#2
Guest Guest Join Date: Sep 2002 Feedback: 0 / 0% Posts: 0 Total Props: 57	Teo things I can suggest. 1. starter box or electric start believe me you will thank me 2. for god sake sell that boat anchor and buy an OS
	.

12-24-2004, 11:36 AM	#4
John Bakker ~~BANNED PEOPLE~~ I am: JB Join Date: Jun 2004 Location: ON Feedback: 0 / 0% Posts: 2,746 Total Props: 0	Sounds like you have an air leak.Check the fuel lines,feul filter ,gas tank,carb boot ,o rings...
	.

12-24-2004, 01:24 PM	#5
imported_sevenstar Join Date: Nov 2004 Feedback: 0 / 0% Posts: 142 Total Props: 0	thanx for the input OS I know they are good motors but I have a os 18 in my t-maxx and it works fine but my savage kicks a-- with that picco and the motor is broken in a long time ago I replaced the o-ring it the high speed valve and that did nothing for it. Starter box noway...I was thinking about a tiger drive to replace the pullstart problem!!
	.

12-24-2004, 03:48 PM	#6
imported_REVOS5 RCC Master Contributor Join Date: Jun 2004 Feedback: 0 / 0% Posts: 1,026 Total Props: 0	get a simple hpi roto
	.

12-24-2004, 06:46 PM	#7
Abiye RCC Pro Contributor I am: joe blow Join Date: Sep 2004 Location: city Feedback: 0 / 0% Posts: 1,715 Total Props: 0	take the motor apart and seal the carb and backplate with permatex ultra copper... make sure your head screws and glow plug are tight... i'm pretty sure you've got some experince tuning since you have a tmaxx and savage but check the idle screw as well... since its coldoutside you need to richen up the mixture... even though the engine temps will be low... but i'm pretty sure u knew all that... just take it apart and seal it... while its apart you can check if there is anything physically wrong with it...
	.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

vBulletin Message

Cancel Changes

Register Now

Log-in