Register Now

Pauld · 01-30-2006, 09:56 PM

Worst is I bent the crank on my engine.... it's toast. I have a Saito 72 out for repair and once I get it back the profile will be back in the air again. I need to get some flight time on my new DV anyways sooooooo..... no more excuses. I'll just fly it a little higher up....

Paul

hillmanr2 · 01-31-2006, 06:45 PM

Quote:

Originally Posted by Pauld

I'll just fly it a little higher up....

Paul

Higher? Just don't make mistakes. LOL

hillmanr2 · 02-12-2006, 06:13 PM

Well I pretty much got this plane flying well as follows
cg 4 3/4 inch from leading edge at the fuse.
1/4 oz of lead on the light wing
thrust angle 0 degree down, 0 right
10% aileron differential
throttle to elev mix
throttle to rudder mix
rud to aileron mix
rud to elev mix
OS 50 sx w/ 13x4 apc 10% xp fuel
jr 537 all around at 6volts
Trimming time 5 hours total so far

It's still a kick around plane but for $120 bucks I'm having fun with it. hovers at just less than half throttle

Pauld · 02-13-2006, 05:48 PM

Jeez Russ,

All them mixes makin my head spin

Good to meet you on Saturday.

See ya at the pattern primer.

Paul

hillmanr2 · 02-13-2006, 06:00 PM

It was good to meet you as well, I really look forward to flying with you.

01-30-2006, 09:56 PM	#21
Pauld RCC Supreme Contributor I am: Paul D Join Date: Apr 2005 Location: Coquitlam, B.C. Radio of choice: Fubar S-bus2 -no lock outs :) # of RCs: 10+ Feedback: 19 / 100% Posts: 3,267 Total Props: 41	Remove this ad - become a site supporter! Worst is I bent the crank on my engine.... it's toast. I have a Saito 72 out for repair and once I get it back the profile will be back in the air again. I need to get some flight time on my new DV anyways sooooooo..... no more excuses. I'll just fly it a little higher up.... Paul __________________ Paulomite http://www.jetpilots.org/ MAAC Jet Committee IF IT'S TOO LOUD - YOU'RE TOO OLD! 2L club executive member
	.

02-12-2006, 06:13 PM	#23
hillmanr2 RCC Supreme Contributor Join Date: May 2005 Location: Kelowna, B.C. Feedback: 0 / 0% Posts: 2,435 Total Props: 0	Well I pretty much got this plane flying well as follows cg 4 3/4 inch from leading edge at the fuse. 1/4 oz of lead on the light wing thrust angle 0 degree down, 0 right 10% aileron differential throttle to elev mix throttle to rudder mix rud to aileron mix rud to elev mix OS 50 sx w/ 13x4 apc 10% xp fuel jr 537 all around at 6volts Trimming time 5 hours total so far It's still a kick around plane but for $120 bucks I'm having fun with it. hovers at just less than half throttle __________________ SUPPORT OUR TROOPS Imac # 4751 Speedway and Hobby http://www.duralitebatteries.com/ PTA Hobbies
	.

02-13-2006, 05:48 PM	#24
Pauld RCC Supreme Contributor I am: Paul D Join Date: Apr 2005 Location: Coquitlam, B.C. Radio of choice: Fubar S-bus2 -no lock outs :) # of RCs: 10+ Feedback: 19 / 100% Posts: 3,267 Total Props: 41	Jeez Russ, All them mixes makin my head spin Good to meet you on Saturday. See ya at the pattern primer. Paul __________________ Paulomite http://www.jetpilots.org/ MAAC Jet Committee IF IT'S TOO LOUD - YOU'RE TOO OLD! 2L club executive member
	.

02-13-2006, 06:00 PM	#25
hillmanr2 RCC Supreme Contributor Join Date: May 2005 Location: Kelowna, B.C. Feedback: 0 / 0% Posts: 2,435 Total Props: 0	It was good to meet you as well, I really look forward to flying with you. __________________ SUPPORT OUR TROOPS Imac # 4751 Speedway and Hobby http://www.duralitebatteries.com/ PTA Hobbies
	.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

vBulletin Message

Cancel Changes

Register Now

Log-in