Register Now

murp · 05-24-2007, 07:48 PM

I am running the 500TH/13TH with 335 Align Pro Woodies - lots of pop - what are others running?

I tried my Align 315 Carbon blades that came with the SE - not very impressive by comparison to the 335 Pro Woodies - anyone else having success running these blades?

martinic · 05-25-2007, 04:50 AM

I'm running the 500TH 14T with TP 2070 3S Extremes, governed using a CC35 at 2800 RPM. I'm currently flying the white Align 325 CF blades (nice), but I was using the 325 Pro blades with similar results.

The climbout is great. The motor (~25 Celcius at 20 C ambient - measured at indoor last month) and batteries come down cool (~34 Celcius) after 5 minutes of hard flying.

Heli3dflyr · 05-25-2007, 10:37 AM

I run the 500TH on 14T with a Jazz 40 in GOV mode at 3200RPM. TPX 2070/2200's get 5.5 minutes. I have tried Hyperions, Radix, V-Blades, 315/325/335 Pro woods, and the Radix seem to be the best all around blades. The V's are the stiffest, coolest sounding blades, and a little less efficient then the Radix. I fly the 325 Pro's most of the time, I crash to much to have Radix on all the time

murp · 05-25-2007, 11:23 AM

I am going to have tryout a 14T - I think the 335 Pro woodies are pretty good for the price. Someday I will convince myself to fork over the dough for the radix blades.

My 315 carbons from align track perfectly - I think I am just used to having a larger rotor disc (and hence more punch). I'll give the 325 carbons from align a try.

martinic · 05-25-2007, 11:39 AM

The white Align 325 CFs look like SABs on the inside (pink foam filled) - ask me how I know.

murp · 05-25-2007, 12:27 PM

where did you get them from?

martinic · 05-25-2007, 01:11 PM

RC Flight Store. I bought 3 pairs, busted one (and a whole lot of other stuff) within 3 seconds of takeoff (tail linkage let go while I was ~6" off the ground - poor workmanship on my part - not enough JB Weld).

murp · 05-25-2007, 04:47 PM

It doesn't look like he carries them anymore

martinic · 05-25-2007, 05:31 PM

Align is having problems keeping up with the demand for that product. They even have had to sub Pro blades in the v2 kits (reducing the price too) because of this supply issue.

Heli3dflyr · 05-25-2007, 08:24 PM

How much did he carry the White CF's for? He has the best price on radix 325's I have seen, you should try some of those Murp

05-24-2007, 07:48 PM	#1
murp RCC Senior Contributor I am: Chad M Join Date: Jan 2006 Location: Nova Scotia Feedback: 0 / 0% Posts: 519 Total Props: 0	500TH/Pinion/Blade combo on Trex SE Remove this ad - become a site supporter! I am running the 500TH/13TH with 335 Align Pro Woodies - lots of pop - what are others running? I tried my Align 315 Carbon blades that came with the SE - not very impressive by comparison to the 335 Pro Woodies - anyone else having success running these blades? __________________ MAAC #75849 Trex 450 Pro stock, Outrage XP30 3S, Fasst Rx Vibe 50 RL53, MP5 SB, Edge 603mm, 3 x s9252, s9452, DS650, Spartan DS760, ATG V3, Fasst Rx
	.

05-25-2007, 10:37 AM	#3
Heli3dflyr RCC Master Contributor I am: Alex D Join Date: Sep 2005 Location: Barrie, Ontario Feedback: 9 / 100% Posts: 1,450 Total Props: 0	I run the 500TH on 14T with a Jazz 40 in GOV mode at 3200RPM. TPX 2070/2200's get 5.5 minutes. I have tried Hyperions, Radix, V-Blades, 315/325/335 Pro woods, and the Radix seem to be the best all around blades. The V's are the stiffest, coolest sounding blades, and a little less efficient then the Radix. I fly the 325 Pro's most of the time, I crash to much to have Radix on all the time __________________ MAAC Member #75939 TRex 600N Pro FBL, TRex 600E CF, T-500E GF, T-Rex 450L 6S Dominator, TRex 550 DFC, DJI Phantom, DJI 550 H33d, DJI S1000 Z15
	.

05-25-2007, 11:23 AM	#4
murp RCC Senior Contributor I am: Chad M Join Date: Jan 2006 Location: Nova Scotia Feedback: 0 / 0% Posts: 519 Total Props: 0	I am going to have tryout a 14T - I think the 335 Pro woodies are pretty good for the price. Someday I will convince myself to fork over the dough for the radix blades. My 315 carbons from align track perfectly - I think I am just used to having a larger rotor disc (and hence more punch). I'll give the 325 carbons from align a try. __________________ MAAC #75849 Trex 450 Pro stock, Outrage XP30 3S, Fasst Rx Vibe 50 RL53, MP5 SB, Edge 603mm, 3 x s9252, s9452, DS650, Spartan DS760, ATG V3, Fasst Rx
	.

05-25-2007, 12:27 PM	#6
murp RCC Senior Contributor I am: Chad M Join Date: Jan 2006 Location: Nova Scotia Feedback: 0 / 0% Posts: 519 Total Props: 0	where did you get them from? __________________ MAAC #75849 Trex 450 Pro stock, Outrage XP30 3S, Fasst Rx Vibe 50 RL53, MP5 SB, Edge 603mm, 3 x s9252, s9452, DS650, Spartan DS760, ATG V3, Fasst Rx
	.

05-25-2007, 04:47 PM	#8
murp RCC Senior Contributor I am: Chad M Join Date: Jan 2006 Location: Nova Scotia Feedback: 0 / 0% Posts: 519 Total Props: 0	It doesn't look like he carries them anymore __________________ MAAC #75849 Trex 450 Pro stock, Outrage XP30 3S, Fasst Rx Vibe 50 RL53, MP5 SB, Edge 603mm, 3 x s9252, s9452, DS650, Spartan DS760, ATG V3, Fasst Rx
	.

05-25-2007, 04:50 AM	#2
martinic RCC Master Contributor I am: Calvin Martini Join Date: Jan 2005 Location: Riverview, NB, Canada Radio of choice: Spektrum # of RCs: 5 Feedback: 8 / 100% Posts: 1,408 Total Props: 7	I'm running the 500TH 14T with TP 2070 3S Extremes, governed using a CC35 at 2800 RPM. I'm currently flying the white Align 325 CF blades (nice), but I was using the 325 Pro blades with similar results. The climbout is great. The motor (~25 Celcius at 20 C ambient - measured at indoor last month) and batteries come down cool (~34 Celcius) after 5 minutes of hard flying.
	.

05-25-2007, 11:39 AM	#5
martinic RCC Master Contributor I am: Calvin Martini Join Date: Jan 2005 Location: Riverview, NB, Canada Radio of choice: Spektrum # of RCs: 5 Feedback: 8 / 100% Posts: 1,408 Total Props: 7	The white Align 325 CFs look like SABs on the inside (pink foam filled) - ask me how I know.
	.

05-25-2007, 01:11 PM	#7
martinic RCC Master Contributor I am: Calvin Martini Join Date: Jan 2005 Location: Riverview, NB, Canada Radio of choice: Spektrum # of RCs: 5 Feedback: 8 / 100% Posts: 1,408 Total Props: 7	RC Flight Store. I bought 3 pairs, busted one (and a whole lot of other stuff) within 3 seconds of takeoff (tail linkage let go while I was ~6" off the ground - poor workmanship on my part - not enough JB Weld).
	.

05-25-2007, 05:31 PM	#9
martinic RCC Master Contributor I am: Calvin Martini Join Date: Jan 2005 Location: Riverview, NB, Canada Radio of choice: Spektrum # of RCs: 5 Feedback: 8 / 100% Posts: 1,408 Total Props: 7	Align is having problems keeping up with the demand for that product. They even have had to sub Pro blades in the v2 kits (reducing the price too) because of this supply issue.
	.

05-25-2007, 08:24 PM	#10
Heli3dflyr RCC Master Contributor I am: Alex D Join Date: Sep 2005 Location: Barrie, Ontario Feedback: 9 / 100% Posts: 1,450 Total Props: 0	How much did he carry the White CF's for? He has the best price on radix 325's I have seen, you should try some of those Murp __________________ MAAC Member #75939 TRex 600N Pro FBL, TRex 600E CF, T-500E GF, T-Rex 450L 6S Dominator, TRex 550 DFC, DJI Phantom, DJI 550 H33d, DJI S1000 Z15
	.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

vBulletin Message

Cancel Changes

Register Now

Log-in