Engines - Page 5 - RCCanada - Canada Radio Controlled Hobby Forum
RCCanada - Canada's Radio Control Hobby Forum
Offroad RC Discussion RC Offroad chat for truggies, buggies, short-course and more. Topics may include brands like Associated, Kyosho, Tamiya, Axial, Traxxas and more.

Closed Thread
Thread Tools Display Modes
Old 04-04-2007, 07:17 PM   #41
Resident complainer
POWLING's Avatar
Join Date: Jan 2006

Feedback: 0 / 0%
Posts: 1,644
Total Props: 0

       Remove this ad - become a site supporter!
hahahahahaha...put that rubber band around the throttle trigger and leave...best way
POWLING is offline   Quick reply to this message.

Sponsored Links - Subscribe to remove this ad.
Old 04-06-2007, 05:57 PM   #42
RCC Pro Contributor
I am: Muckey M
Join Date: Feb 2005
Location: disneyland Ontario

Feedback: 0 / 0%
Posts: 1,946
Total Props: 0

This was copied from a post by STEPHEN BESS on the "Starting Grid" message board as he tried to help another member get more life and performance out of his OS motor. This break-in method should apply to virtually any ABC hobby nitro engine (except for ringed engines).

If you are still idling at least a tank through during break-in, you're using the old-school accepted method (still works well for some!) but it's not the method that the top engine guys (Ron Paris, Dennis Richey, Rody Roem, Michael Salven are just a few I've spoken personally with about this) recommend anymore.

From the very 1st time you start your engine, plop the car on the ground & begin running it in a parking lot in 2-3 minute intervals, tuned only *slightly rich* getting the temps up in the 200F range on a normal day. Every 2-3 minutes, shut the engine down & let it cool completely with the piston at BDC, and then fire it back up; continue this cycle until you've run 15 min or so, and then bump up to 3-4 minute intervals. Vary the RPM and don't be afraid to get the temps in the 200's. What you want is heat cycling of the components without the incredible stress that comes with breaking an engine in when it's overly rich & cold. After cycling the engine in this mannerfor about 20-25 total minutes, it'll be ready for the track and race tuning. I realize this method goes against the old-school "idle on the box" routine, but you'll be amazed once you've completed this break-in routine, your OS will still have amazing pinch w/out sticking at the top AND your OS's compression will last far longer than it will with the "old school" method.

You say you run the engine at "factory settings" for the first FIVE tanks? That alone causes lots of stress, as the factory OS settings are very rich on every OS I've ever owned or tuned. The piston & sleeve haven't expanded to operating temps, and every time the engine turns over, the piston slams into the pinch zone at TDC. The not-so-surprising result can be a cracked con-rod at the crank pin--that's where the majority of the stresses occur as the engine turns over. I've only heard of about 6-8 OS engines breaking con-rods, and they're ALWAYS during the first gallon...and almost every time it's because the guys have performed the break-in procedure you described. Doesn't seem like a mystery as to why it's happening. Drawing out the break-in routine really stresses the engine & actually wears away compression along the way. This method I've outlined will feel weird at every step, but after you try it once, you'll notice a big difference in your engine's performance & lifespan.

Hope this helps; give this break-in method a shot--you have nothing to gain except longer life & more power

I would use something like this.
Mugenman is offline   Quick reply to this message.
Old 04-06-2007, 05:58 PM   #43
RCC Pro Contributor
I am: Muckey M
Join Date: Feb 2005
Location: disneyland Ontario

Feedback: 0 / 0%
Posts: 1,946
Total Props: 0
There are a lot of variations of this method. I believe I have the Ron Paris method as well somewhere.

Good Luck and enjoy !
Mugenman is offline   Quick reply to this message.
Closed Thread

Quick Reply

Register Now

In order to be able to post messages on the RCCanada - Canada Radio Controlled Hobby Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

Member names may only be composed of alpha-numeric characters. (A-Z and 0-9)

!!ATTENTION ADVERTISERS!! If you intend on advertising anything on this forum, whatsoever, you are required to first contact us here . Additionally, we do NOT allow BUSINESS NAMES unless you are an Authorized Vendor. If you own a business, and want to do sales on this site via posting or private message, you will need to follow the rules. Shops, Stores, Distributors, Group Buys without being authorized will see your account terminated.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Your Name
Your first name and last initial is required if you plan on using the forum.
Which city & province you live in. This is mandatory for classified listings.
Radio of choice?
Which radio is your current favorite to use?
Number of RC Vehicles?
How many boats, cars, planes do you own?


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
vBulletin Message

Thread Tools
Display Modes

Forum Jump

All times are GMT -5. The time now is 03:26 PM.

vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2016 DragonByte Technologies Ltd.