2 Brand new electric motors and 2 100Amp esc - RCCanada - Canada Radio Controlled Hobby Forum
RCCanada - Canada's Radio Control Hobby Forum
FS - Electric Gear Post your electric gear for sale here. Electric motors, batteries, ESCs, etc...

Closed Thread
Thread Tools Display Modes
Old 01-05-2016, 08:23 AM   #1
RCC Junior Contributor
I am: Adam Pelletier
Join Date: Jun 2009
Location: Beresford, New Brunswick
Radio of choice:
Spectrum 7ch 2.4G
# of RCs: 20

Feedback: 12 / 100%
Posts: 170
Total Props: 0
2 Brand new electric motors and 2 100Amp esc

Power Plant: Electric
New or Used: Item is new, unused
Trades: No trades.
Asking Price: $160.00
Accepted forms of payment: EMT, Paypal
Shipping : I will not ship.
My Location: e8k1e8

       Remove this ad - become a site supporter!
I have for sale 2 electric setups brand new never used bought and put aside for other larger RC projects but had to make room for new toy, so Iím selling the two setups as a lot, may separate if price is right but would prefer to sell as lot make me an offer items are below what I paid for them. Price includes shipping to anywhere in Canada, to the USA other charges may apply. Thanks for looking

1- Standard accessory pack for NTM Prop Drive 50 and 35 series motors.
CNC Machined (take a close look at the cross mount, even that is machined rather than punched) from billet 6061 alloy for strength and balance.
Shaft Diameter: 8mm
Shaft Length: 36mm
Cross Plate Bolt Holes: 62mm
Weight: 55.1g (Total)

1- NTM Prop Drive motors are rock-solid performance out runners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings plus they are QC checked at 14 points, from material processing all the way through to final dyno test.

Model: NTM Prop Drive Series 5060 380kv
Kv: 380rpm/v
Poles: 7
Max current: 90A
Max Power: 2665W @ 30v (8S) / 2000W @ 22v (6S)
Shaft: 8mm
Weight: 468g
ESC: 100A
Cell count: 6s~8s Lipoly
Bolt holes: 30mm
Bolt thread: M4
Connection: 4mm Bullet-connector
Prop Tests:
17x8 - 25.9v - 1900W - 73.5A - 7.03kg thrust
17x10 - 25.9v - 2124W - 82A - 7.26kg thrust

2- Turnigy AE-100A Brushless ESC

The Turnigy AE series are based on new powerful microprocessor.
The new CPU means ultra-fast sync timing, crisper throttle response, less battery load and reduced FET heat buildup. Also there is a separate voltage regulator IC for microprocessor providing good anti-jamming capability.
Output: Continuous 100A, burst 115A up to 10 seconds.
Input Voltage: 2-6 cells lithium battery or 5-18 cells NIMH battery.
BEC: Linear 4A @ 5V
Control Signal Transmission: Optically coupled system.
Max Speed:
2 Pole: 210,000rpm
6 Pole: 70,000rpm
12 Pole: 35,000rpm
Size: 71mm (L) * 34mm (W) * 17mm (H).
Weight: 79g.

High performance microprocessor brings out the best compatibility with all kinds of motors and the highest driving efficiency.
Wide-open heatsink design to get the best heat dissipation effect.
Improved Normal, Soft, Very-Soft start modes, compatible with aircraft and helicopter.
Smooth, linear, quick and precise throttle response.
Multiple protection features: Low-voltage cut-off protection / Over-heat protection / Throttle signal loss protection
Programable via transmitter and Turnigy BESC programming card
Programming features:
Brake setting (we recommend using brake for only folding props applications)
Battery type(Li-xx or Ni-xx)
Low voltage cutoff setting
Factory default setup restore
Timing settings (to enhance ESC efficiency and smoothness)
Soft acceleration start ups (for delicate gearbox applications)
Low voltage cutoff type (power reduction orirnmediate shutdown)
Governor mode
Built-in BEC Output(5.25V or 6V)

Factory default settings:
Brake: off
Battery type: Li-xx (Li-ion or Li-Po)
Low voltage cutoff threshold: Soft cut-off (2.6V)
Timing setup: Low
Soft Acceleration Start Up: Normal
Low voltage cutoff type: Medium

1- NTM Prop Drive 35-48 Series 900KV / 815W

NTM Prop Drive motors are rock-solid performance outrunners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings plus they are QC checked at 14 points, from material processing all the way through to final dyno test.

Model: NTM Prop Drive Series 3548 900kv
Kv: 900rpm/v
Poles: 3
Motor Wind: 7T
Max current: 55A
Max Power: 570W @ 12v (3S) / 815W @ 15v (4S)
Shaft: 5mm
Weight: 171g
ESC: 60A
Cell count: 3s~4s Lipoly
Bolt holes: 18.9mm & 25mm
Bolt thread: M3
Connection: 3.5mm Bullet-connector

I am asking $ 160.00 canadian shipped for the whole lot if interested please contact me by sending me a PM, I will respond promply, I except email money transfer and paypal thanks for looking.

================================================== =======
RCC Classified Quick Rules

- Location & price is a must when selling RC related items. Update your profile!!!
- Use the feedback system after a sale / trade.
- Buyer Beware!
- One bump / TTT every 3 days.
- Classified rules here.
** Infractions will be passed out if rules are broken. Threads may be deleted.

================================================== =======
Attached Thumbnails
Click image for larger version

Name:	19341(1).jpg
Views:	37
Size:	53.6 KB
ID:	795786   Click image for larger version

Name:	23521.jpg
Views:	42
Size:	41.8 KB
ID:	795794   Click image for larger version

Name:	28888.jpg
Views:	37
Size:	80.1 KB
ID:	795802   Click image for larger version

Name:	NTM3548-900.jpg
Views:	41
Size:	53.6 KB
ID:	795810  

Top Flite Fw-190D, Sig Bravo, Sig 1/4 Piper Cub,
Sig 1/7 Piper Cub, Pica 1/7 Spitfire, Grupner Lazer,
Pica 1/5 Cessna 182, Pattern Atlanta .60,
Hobbico Nextar, 1/5 Cessna 185 Scratch Built

Last edited by cooler; 01-06-2016 at 06:10 AM.
cooler is offline  

Sponsored Links - Subscribe to remove this ad.
Closed Thread

electric , motor , ecs

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
vBulletin Message

Thread Tools
Display Modes

Forum Jump

All times are GMT -5. The time now is 08:20 PM.

vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2016 DragonByte Technologies Ltd.