RCCanada - Canada Radio Controlled Hobby Forum

RCCanada - Canada Radio Controlled Hobby Forum (https://www.rccanada.ca/rccforum/index.php)
-   General RC Heli Discussion (https://www.rccanada.ca/rccforum/forumdisplay.php?f=84)
-   -   synergy e5 ss project (https://www.rccanada.ca/rccforum/showthread.php?t=584017)

imported_rnst2 10-03-2019 08:31 AM

16 Attachment(s)
planning to ss my e5.
cheaper route for me to go 700.
any help/input is appreciated.
just excited with the thought.
thanks in advance.

rotorsport 10-14-2019 10:23 PM

Re: synergy e5 ss project
Here is a link of the build done by a member in my club


imported_rnst2 10-15-2019 07:34 PM

Re: synergy e5 ss project
got my parts en route.

imported_rnst2 10-27-2019 10:46 AM

Re: synergy e5 ss project
another obstacle. well, my new hw esc would not power
my fbl controller. tried my 6s esc and it powers it.
is my hw esc faulty?
cant get into bec parameters w/ the box.
i have two on those prgrm box.
but no use as it wont power up the fbl.
need help.
and i thought i could spin this thing today.
thanks in advance.

Dennis Pedersen 10-27-2019 11:19 AM

Re: synergy e5 ss project
Not sure what HW esc you have but I assume a 130HV. How do you have your series adapter made for plugging in you battery packs. Also with your battery packs plugged in have you tried plugging your BEC wire into the the battery checker on the RH side of your HW programmer box to see what the voltage coming out is. Hope you get your E5 SS going , I really liked mine.

imported_rnst2 10-27-2019 12:09 PM

Re: synergy e5 ss project
4 Attachment(s)
hi Dennis,
thanks for taking the time.
130amps v4. tried the bec wire on the side and it wont do anything to the box(plugged from the side). led is blinking. i can make changes on parameters except the bec output as it doesnt go to the window, skipped to the next item.
too bad i have to go to bed for a night shift later.
just dont why it wont power the fbl.

imported_rnst2 10-27-2019 12:10 PM

Re: synergy e5 ss project
those pics are with hw esc and tribs esc.
i think my series wire is legit ��.
thanks again

Dennis Pedersen 10-27-2019 04:32 PM

Re: synergy e5 ss project
2 Attachment(s)
Have you seen if you have power on the BEC RPM port?


imported_rnst2 10-27-2019 06:56 PM

Re: synergy e5 ss project
found the answer. it’s an ‘opto’ model.
it has an rpm/bec port, but the model doesn’t support bec.
just need an rx batts.

THANKS for the time and replies.

Dennis Pedersen 10-27-2019 07:07 PM

Re: synergy e5 ss project
That would do it ! Now you need to pick up a great Western Robotics BEC for it.

All times are GMT -5. The time now is 07:19 AM.

Powered by vBulletin®
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Powered by vBA CMPS
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.