Wanted 120 size motor mount - RCCanada - Canada Radio Controlled Hobby Forum
RCCanada - Canada's Radio Control Hobby Forum
Wanted - Other Other aircraft related items you may be looking for.

Reply
 
Thread Tools Display Modes
Old 05-11-2020, 04:13 PM   #1
skymaster337
RCC Senior Contributor
 
skymaster337's Avatar
 
I am: George K
Join Date: Aug 2003
Location: Tara, Ont.

Feedback: 23 / 100%
Posts: 510
Total Props: 1
Wanted 120 size motor mount

My Location: Tara, Ont N0H2N0


       Remove this ad - become a site supporter!
Looking for a motor mount for a 120 Enya 4 stroke
Let me know what you have and how much shipped to N0H2N0

================================================== =======
RCC Classified Quick Rules

- Location & price is a must when selling RC related items. Update your profile!!!
- Use the feedback system after a sale / trade.
- Buyer Beware!
- One bump / TTT every 3 days.
- Classified rules here.
** Infractions will be passed out if rules are broken. Threads may be deleted.

================================================== =======
skymaster337 is offline  

Sponsored Links - Subscribe to remove this ad.
Old 05-11-2020, 08:19 PM   #2
Cougar429
Level 3 Supporter
★ Site Supporter ★
 
Cougar429's Avatar
 
I am: Gary L
Join Date: Aug 2008
Location: Tecumseh, Ontario

Feedback: 99 / 100%
Posts: 7,165
Total Props: 46
Re: Wanted 120 size motor mount


If you can give beam spacing and length you need, (short or long nose) I have lots of spare mounts. Also have universal composite type where the two halves are adjustable.
__________________
I know there's money in aviation........I put it there!
Cougar429 is online now  
Old 05-12-2020, 08:00 AM   #3
skymaster337
RCC Senior Contributor
 
skymaster337's Avatar
 
I am: George K
Join Date: Aug 2003
Location: Tara, Ont.

Feedback: 23 / 100%
Posts: 510
Total Props: 1
Re: Wanted 120 size motor mount


Good point Cougar 429, Beam width of 1 7/8 inches and long nose, (I have 3 1/2 inches from carb at rear to front of beam mounting tab)
skymaster337 is offline  
 
Old 05-12-2020, 09:18 AM   #4
Cougar429
Level 3 Supporter
★ Site Supporter ★
 
Cougar429's Avatar
 
I am: Gary L
Join Date: Aug 2008
Location: Tecumseh, Ontario

Feedback: 99 / 100%
Posts: 7,165
Total Props: 46
Re: Wanted 120 size motor mount


Those dims are useful and will see what I have, but one thing was looking for was how long a beam you needed to get the nose to where required. There are short and long beam mounts, although in most cases I have seen the adjustable are only one length.

Again, will check in a few. Just got up again and waking up......

I do know the one adjustable should work as I was test fitting an OS 120 recently.
__________________
I know there's money in aviation........I put it there!

Last edited by Cougar429; 05-12-2020 at 10:07 AM.
Cougar429 is online now  
Old 05-12-2020, 10:07 AM   #5
Cougar429
Level 3 Supporter
★ Site Supporter ★
 
Cougar429's Avatar
 
I am: Gary L
Join Date: Aug 2008
Location: Tecumseh, Ontario

Feedback: 99 / 100%
Posts: 7,165
Total Props: 46
Re: Wanted 120 size motor mount


O/K. Found three possibles. From left to right two are adjustable and could work. Only thing is they have been drilled and tapped and spacing may not work for your engine. Even if slightly off you can drill and bolt with lock nuts from the bottom. Beam length is 4 3/8 from mount face, and 3 7/8 from front of mount face.

Last one on the right is a bit strange. Spacing at the mount face is 1 7/8, but shrinks to 1 3/4 at the nose so there is some mold deformity or it did that when it cooled. Other issue is it is 3 1/2" from the mount face so carb and inlet tube may have to be hogged into the mount to get it to fully engage the beams.

Only other ones I had were steel and 4" wide.
Attached Thumbnails
Click image for larger version

Name:	DSCF1757.jpg
Views:	18
Size:	653.7 KB
ID:	1673709  
__________________
I know there's money in aviation........I put it there!
Cougar429 is online now  
Old 05-12-2020, 03:07 PM   #6
skymaster337
RCC Senior Contributor
 
skymaster337's Avatar
 
I am: George K
Join Date: Aug 2003
Location: Tara, Ont.

Feedback: 23 / 100%
Posts: 510
Total Props: 1
Re: Wanted 120 size motor mount


The very far left one would work for me. If you could mail me that one what would I emt you?
Thanks
skymaster337 is offline  
Old 05-12-2020, 03:45 PM   #7
Cougar429
Level 3 Supporter
★ Site Supporter ★
 
Cougar429's Avatar
 
I am: Gary L
Join Date: Aug 2008
Location: Tecumseh, Ontario

Feedback: 99 / 100%
Posts: 7,165
Total Props: 46
Re: Wanted 120 size motor mount


Will look for a box and check shipping costs and let you know.
__________________
I know there's money in aviation........I put it there!
Cougar429 is online now  
Old 05-16-2020, 08:23 AM   #8
floyd
Level 3 Supporter
★ Site Supporter ★
 
I am: Floyd S
Join Date: Feb 2009
Location: Stayner, Ontario

Feedback: 198 / 100%
Posts: 3,864
Total Props: 16
Re: Wanted 120 size motor mount


PM sent. Cheers Floyd
floyd is offline  
Old 05-16-2020, 09:05 AM   #9
COSMOS
RCC Pro Contributor
 
I am: robert l
Join Date: Jan 2006
Location: laval, québec

Feedback: 163 / 100%
Posts: 1,601
Total Props: 0
Re: Wanted 120 size motor mount


I have one Aluminum Tatone with mounting hardwares
See the attached pictures
Pm
Cosmos
Attached Thumbnails
Click image for larger version

Name:	DSC01642.jpg
Views:	10
Size:	419.2 KB
ID:	1674117   Click image for larger version

Name:	DSC01643.jpg
Views:	7
Size:	478.0 KB
ID:	1674119   Click image for larger version

Name:	DSC01644.jpg
Views:	6
Size:	548.9 KB
ID:	1674121   Click image for larger version

Name:	DSC01645.jpg
Views:	7
Size:	395.0 KB
ID:	1674123  

COSMOS is online now  
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
vBulletin Message

Thread Tools
Display Modes

Forum Jump


All times are GMT -5. The time now is 08:33 AM.


vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.